Today, I washed my hands at the kitchen sink while making lunch, and was unexpectedly chastised by my partner because she had just started the dishwasher. Apparently, she has recently come across something that has convinced her that running the hot water in your sink means the water that enters your dishwasher will be hotter (checks out), and thus the dishes will be cleaner. I tried searching startpage to see if this is real, but I couldn’t make it through even one llm-slop-ticle about it before my eyes rolled back into my head, so here I am asking y’all: chat, is this real? Doesn’t my dishwasher have a heating element? Is there any meaningful difference between heating the water with a hot water heater vs a dishwasher, other than I can’t use my sink while the dishwasher is filling and I have to pour a bunch of cool water down the drain?
Your dishwasher uses hot water so if you run your sink until hot water is coming out before running your dishwasher it means it’s immediately getting hot water. It’s about clearing the cold water out of your pipe.
Whether or not you can use the sink while the dishes are being washed depends on your water heater. If you can wash your hands while someone is taking a shower without blasting them with cold water then you should be fine to use your sink while the dishes are being washed.
Growing up we had to run the shower until it was hot before we could wash the dishwasher.
In the United States and other countries with 120V electricity
It has nothing to do with 120v electricity. We used to have dishwashers in the USA that could heat water from cold to 140ºF without issues.
I believe one of the technology connections videos talks about making sure the sink water is hot so the dishwasher can have hot water and not clean with cold water
It might be this video
https://www.youtube.com/watch?v=jHP942Livy0One thing I just want to point out that’s stated in the video is the hot water is for the pre treat cycle. It always heats up the water for the main wash cycle.
came to post this. note: this works if your dw is on same line feed as sink. if for some reason it’s not, you can’t purge the cool water away.
Edit: okeedokee I’m wrong.
GE Appliances: Dishwasher - Correct Water Temperature
Ummm…what are all the USA people in here talking about?
I’ve installed and replaced my own dishwashers 4 or 5 times over the years and helped friends and family members many times. They only last about 5-7 years so it happens often enough for it to be routine for me.
The water supply is connected to the cold water. The dishwasher has it’s own heating element. It heats the water to “sanitizing” levels. There’s even a sanitize button.
That water gets so hot that I can’t open the door mid-cycle with my reading glasses or they’ll get completely fogged up.
The sanitize button is not a new development…
They aren’t all designed to connect to your cold water line. In fact, most seem to specifically instruct you to connect to your hot water intake. You are right that most in the US have water heaters, but that doesn’t mean that the machine’s cycles will heat the water effectively for the full duration of the wash.
Maytag, Whirlpool, GE, and LG all recommend you connect to hotwater. Bosch (EDIT: Spelled this like the drug company not the appliance company) recommends cold. Depending on your machines cycles as well, the heating element may not get the water hot enough to make effective use of the pre-wash cycle. If your machine is connected to the hot water line and you purge the cold water from the line, you will see a more effective pre-wash (and thus more effective wash) than if you let it run cold.
North America vs Europe, North America cannot heat the water fast enough due to the limit of being on a 120V and 15 A circuit.
They have 120 volt electricity, it can’t heat quickly enough, so the wash cycle will begin with less than optimal temperature and take a while to get to sanitizing temperature.
So they feed it water from the hot water tank, which isn’t hot enough usually but the heating element can get it up to temp much faster at 120v.
Many modern dishwashers only have a cold water inlet so it literally does not get water from the hot water tank.
120V really doesn’t matter that much as they are commonly on their own 20A breaker. At 1500W of power it can heat 1.5L of water from 60F to 168F in 1 minute.
Where are you getting your information? Can you find an example of a dishwasher where the installation manual says to use cold water?
And the claim that 120v doesn’t matter is baseless.
At 1500W of power it can heat 1.5L of water from 60F to 168F in 1 minute
Lol no it can’t, are you nuts? That’s physically impossible and mathematically incorrect by a factor of more than 4.
My information is based on installing 3 dishwashers in the US that all said to either connect to cold water or give an option for cold water or hot water
Voltage doesn’t matter for heating what matters is overall power. 1500W at 120V and 1500W at 450V both heat at the same rate. The advantage of higher voltage home systems is they usually allow higher power since current is generally the limiting factor but they make higher current breakers for 120V
I was off on my conversions and did calories instead of joules. Either way it takes 4 minutes to get from 60 to 160 which is still trivial on a multi hour cycle
Here is one that allows either connection but emphasizes increased efficiency with hooking up to cold water. I admitted I was wrong on my conversions will you admit you are wrong that they have to hook up to hot water?
Here is one that allows either connection but emphasizes increased efficiency with hooking up to cold water.
"For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. Hot water supply specifications: Recommended temperature: 120 °F (49 °C), max 140.
will you admit you are wrong that they have to hook up to hot water?
So weird. You want to be right? Okay, you’re right, you don’t have to hookup to a hot water, it’s recommended and commonly done… I don’t think I claimed you have to… The reason it’s recommended to hook to hot water is because it’s slower at 120v. They all allow you to do whatever the hell you want, but American tap water (which doesn’t sit in a rooftop tank that gets warm as it sits around, but that doesn’t apply much in the northern hemisphere) is typically not ideal.
You want your dishwasher to take longer? hook it up to cold water and save some electricity, you do you.
1500W at 120V and 1500W at 450V
Why would I use 1500W at 240V? My dishwasher has a 2100W heating element, which heats 40% faster, that’s not negligible. You can get higher wattage models.
You installed 3 dishwashers? That doesn’t make you an expert on international dishwashers, it just makes you a homeowner. Jesus, you don’t have to just argue for the sake of arguing, just say “I learned something dumb today” and move on with your life.
You said “Many modern dishwashers only have a cold water inlet so it literally does not get water from the hot water tank” and then provided an example that says what I said, if you want a faster wash use hot water.
The reason most of the world uses the cold tap for dishwasher hookup is because they use a higher wattage heating element, which they can operate safely because they use 220V power. I didn’t come up with the 1500W limit, you did, don’t move the goal posts.
You probably have higher voltage and more power going to that heating element, so the cold water line is fine. In the US, the heating elements in our dishwasher can’t draw enough power for cold water, so it needs to start with hot water.
Also, 5-7 years is… Pretty bad. It’s not uncommon for dishwashers to last multiple decades here. I’m pretty sure mine is at least 20 years old (and ugly lol)
I run the dishwasher every night, even if there’s just a few dirty dishes, so I’m pretty hard on my dishwasher. I use the heck out of it.
It’s caused lots of wailing and gnashing of teeth in my family but I can’t stand unloading a dishwasher packed to the gills with a week’s worth of clean dishes. Just get it done as part of a daily routine.
Not USA but North America and we ours is hooked to hot water. Has to do with having a shitty heating element since they wanted it to be plugged into 120 15A circuit.
I checked under my cabinet just recently, and the dishwasher is indisputably connected to the hot water line.
It was like this in the last place, too, and my sibling’s place.
https://m.youtube.com/watch?v=jHP942Livy0
Here is a video from someone explaining why you should run the water hot before turning on the dishwasher, along with a few other tips.
Upvote for Technology Connections
My sibling’s dishes won’t get clean unless she runs the water first, as her sink takes a crazy amount of time to warm up.
YMMV though. Not all sink piping takes so long to “warm up” anyway.
So test it!
Run a dirty load. If your dishes get clean in the dishwasher, no problem; your routine ain’t broke. If you aren’t satisfied, try running the hot water first.
It’s certainly not worth an argument with an SO though, as it could plausibly help.
You don’t see the giant bent calrod in the bottom?
I do, based on an older vid from the guy CADmonkey referenced. My hot tap water gets to about 120°F.
Doesn’t work for me. My dishwasher water line is a separate line. It has it’s own valve at the manifold.
It’s just to get the hot water flowing in the hot water line. So your dishwasher doesn’t get as much cold water as it would other wise.
It’s correct if in a country where the dishwasher lacks its own water heater.
Dishwashers in the U.S don’t have water heaters and therefore it’s beneficial to purge lukewarm water from the hot water line before starting the dishwasher, such that the water in the dishwasher is on average hotter and as such more effective at washing the dishes.
Dishwashers in Europe have water heaters and as such it’s entirely irrelevant to do it there
So do dishwashers in North America they are just less powerful because of the 120 volt.
I live in the US and every dishwasher I ever owned had a heating element, and was capable of heating its own water as needed, depending on what cycle was selected.
Same with my washing machines, my current one even has a steam cycle.
I feel like if dishwashers without heating elements were ever a common thing here, it must have been many decades ago.
Its not so much about that, as it is about the fact that they almost always do an initial “clean-off-the-dirtiest-bits” cycle for around 10 minutes which pulls in (mostly) cold water if your line is not purged like the OP describes. And they don’t use the heating element for this initial cycle.
After the first 10 minutes they flush out the super dirty water with the dirtiest food bits and sauce and whatnot, fill in brand new water, and then run for the duration of the washing cycle (1hr plus) along with the heating element.
So flushing the cold water out of your kitchen water lines AND adding pre-wash detergent (such as some extra powder right in the door, outside of the main closable detergent compartment) helps a ton with this initial 10ish minute cycle.
AND adding pre-wash detergent (such as some extra powder right in the door, outside of the main closable detergent compartment) helps a ton with this initial 10ish minute cycle.
Yup, and that’s why some dishwashers include PreWash text somewhere on the side of the door. Sometimes it’s even on that little flap where you put the pod
Dishwashers in the U.S don’t have water heaters
Crazy. Mine only takes in cold water. Never even knew ones that take in hot water existed.
You’ll be surprised to hear that U.S washing machines have the same setup, and this is why they talk about “wash cold” or “wash hot” instead of having specific temperatures on their washing programs like 30 C, 40 C, 60 C etc.
How do you do a 90°C wash? Surely the tap water doesn’t get that hot.
The washing machine heats the water, many go up to 95°C
I wouldn’t know unfortunately, I’m in Europe.
As a European that carefully checks the temperature levels indicated on the clothing before washing, I feel like I did it wrong - or at least overly complicated - my whole life now 😅
It’s because the US electrical system sucks and they refused to upgrade it, although reasonably speaking it would be kind of impossible at this point. In order to be able to actually run a heating element you would have to have a special circuit fitted with a decent voltage.
it’s pretty trivial to combine two hots to get back up to 240. It’s common for industrial and some consumer appliances
Also why US homes tend to have the immersion heater setup for hot water with a big tank that gets heated over time, compared to the common euro system of on-demand instantaneous hot water.
I gotta love how the US is really advanced for the most part but then occasionally you come across one area in which it operates like 1980s Estonia.
The newest construction near me puts tankless in townhomes and full-size in single-family homes. (as long as gas is available)
They’re super efficient when you don’t use tons of hot water because your waste on tank heaters is heat loss through the pipes and heater itself.
The water heaters are usually gas here though, so electric system doesn’t really matter. Tankless heaters have become a lot more common over past decade or two, both gas and electric. For electric ones you just use a 240V circuit. Most electric appliances that need a lot of power run on 240V here, 30A and even 50A or 60A circuits are common and provide enough power for household needs.
Ah that makes sense. Cheers.
I was so sure the answer was going to be no. TIL
Why did your wife chastise you over having cleaner dishes?
The technology connections guy says it helps assuming your dishwasher water connection is at the sink and that the heating element in your washer isn’t very good or efficient.
Detergent packs are kinda wishy-washy (Dishwashers Explained)
Provided your dishwasher is even connected to the warm water line. Typical dishwashers with internal heaters are not. A family member of mine has the dishwasher connected to the warm water line to save on electricity for heating the water (has solarthermal elements on the roof for heating water). Though that can alao mean, that on hot days the warm water line gets too hot for most plastics (like 70°C). A bit inconvenient.
The Technology Connections guy on YouTube thinks so
He also said that with modern detergents, you should do colder washes anyway, as the hot water has little benefit.
If you live in the US. Dishwashers works very differently in Europe for example.
Indeed. Both apartments I’ve lived in (in Europe) had the dishwasher hooked up to the cold water feed, so preheating the water would absolutely do nothing at all.
Ah thanks, I was beginning to question everything I thought I knew about how my dishwasher works.
Reliably having 3 phase 230 V (thus 400 V delta between two phases) makes a big difference from single phase 120 V. Usually rated at 16 A too, available from each phase pair.
Almost 10 kW available at the peak (although almost nothing made for regular homes use it that much, aside from electric cars).
https://everycalculators.com/kilowatt-calculator-3-phase.html
As compared to a US outlet typically limited to 20 A at 120 V in one phase, giving you 2,4 kW (a quarter) or 15 A at 1,8 kW.
I noticed an improvement preheating the water. It’s also probably more energy efficient than letting the dishwasher do it, if it can at all.
They both have electric heating elements so identical efficiency. The advantage is that priming hot water means it’s hotter for longer and reaches a higher peak temperature in the dishwasher, which means more effective cleaning.
Not every home heats their water with electric resistance heating. My previous place used natural gas for hot water, and my current home has a heat pump water heater, which has an effective efficiency much greater than a normal electric water heater.
The heating element in the dishwasher at best maintains the water at a warm temperature. It will not instantly heat the water up for the very short first cycle of prewashing, just like if you suddenly put cold water into a water heater it wouldn’t be suddenly hot. It takes a lot of energy/time to warm water up.
My statement is taken directly from TCs video where he graphed the temps for primed vs unprimed washing. Priming the water leads to hotter (higher peak) and more area under the curve. Not priming leads to lower peak temps, but it’s certainly warmer than at best warm. The element will heat your water up even hotter than it comes out of the primed line, assuming you primed it.
When I open my dishwasher it is absolutely steaming and the dishes are too hot to handle. This temperature is above the setting on the hot water heater, ergo this extra heat can only have come from the heating element. It provides significant extra heat.
You are correct that it will take significantly longer than the prewash cycle’s duration and is not something to be relied on if you want optimal washing.
Technically I think he says that IF your dishes don’t already get clean.
Yeah if you aren’t having issues why make the extra step
Yes. I’ve watched all of them in their entirety
Yes, as many others have said, there is an explanation for running the hot water before turning on the dishwasher.
However, your partner is wrong. The purpose of running hot water is to prime the hot water pipes. Once that’s done you can go ahead and wash your hands with cold water, because the hot water pipe is already full of hot water.
EDIT: just to elaborate on the above comment:
You can run a mix of hot and cold water all you want, if the hot water is on, it still primes the hot water pipes with hot water; they don’t mix until they join in the faucet itself.
Running the hot water at the faucet will fill the hot water pipe with hot water (hasn’t had time to sit and cool down) so your dishwasher’s initial pre wash cycle has a higher temperature water to begin with as it draws from that same pipe; you’re not starting with slightly cooler water and waiting for the heating element to bring it up to temp (at least not as long, usually dishwasher water is slightly hotter than water heater temp).
Running cold water at the sink does not cool the dishwasher’s intake water down. Cold water isn’t mixed with hot until it’s already in the faucet (after the valves you control at the faucet itself). As long as you run the hot until hot water makes it up to the sink itself, you’re golden no matter what else is going on.
Thanks, everyone else was missing this point and I was about to write up something similar.
